Help Center · 20 questions

Nitric Acid & Fertilizer FAQs: Selection, Use & Storage

Find practical answers to common questions about nitric acid, ammonium nitrate, UAN and compound fertilizers. Learn how to compare specifications, calculate nutrient quantities, check equipment compatibility and assess storage or delivery issues. For a specific product, refer to its current specification, batch quality documents and Safety Data Sheet.

Nitric Acid

How do I choose between 40%, 68% and 98% nitric acid, and select the right grade?

Choose the concentration required by your process, then check the grade and impurity limits. The percentages describe nitric acid content by mass; they do not establish suitability for every application. Compare the agreed product specification and batch quality report, including any relevant metal or chloride limits. Provide your intended application, required concentration, operating conditions and critical quality requirements when requesting a recommendation. Changing concentration may also require a review of your process and equipment.

Can my existing tanks, pipes, pumps and seals be used with nitric acid?

Compatibility must be confirmed for the actual operating conditions. Nitric acid concentration, temperature, contact time and the exact material grade all matter. Check every wetted component, including tank linings, hoses, valves, pump parts, gaskets and seals. Descriptions such as “stainless steel” or “plastic” are too general for a reliable decision. Ask the equipment manufacturer to assess the materials and operating conditions. A chemical compatibility chart can support initial screening but cannot approve an entire installation.

My nitric acid has turned yellow. Can I still use it?

Colour alone cannot confirm whether the product remains suitable. Some commercial nitric acid specifications allow a clear to slightly yellow appearance, but an unexpected change should be checked against the specification and storage history. Record the batch number, storage conditions and observations, then contact the supplier before further use. Confirmation may require testing of concentration and application-critical impurities. If there is leakage, container damage or unexpected fuming, follow the SDS and site emergency procedures.

Can nitric acid be used to adjust pH in hydroponic or irrigation systems?

Yes, in a suitable system. Nitric acid lowers pH and neutralizes alkalinity while adding nitrate nitrogen, which must be included in the nutrient programme. Suitability depends on water analysis, crop requirements, product quality and dosing equipment. The starting pH alone cannot determine the acid dose; water alkalinity and the treatment target are also essential. Have an agronomist or irrigation specialist establish the treatment plan, using compatible equipment and trained operators following the product’s SDS.

Ammonium Nitrate

Does “≥99.5% ammonium nitrate” mean the product contains 99.5% nitrogen?

No. Ammonium nitrate content measures the proportion of the compound NH₄NO₃, whereas nitrogen content measures the nitrogen within the product. Pure ammonium nitrate contains approximately 35% nitrogen by mass. Also check whether the stated ammonium nitrate assay is reported on a dry basis or an as-supplied basis, and how moisture is accounted for. For fertilizer comparisons and application calculations, use the product’s declared or guaranteed nitrogen analysis rather than its chemical purity figure.

Can ammonium nitrate, calcium ammonium nitrate and urea replace each other at the same application rate?

Equal product weights usually supply different amounts of nitrogen. Recalculate the replacement quantity using each product’s actual nitrogen analysis, then review the application plan. Nitrogen forms, additional nutrients, soil conditions, weather and placement can affect nutrient availability and losses. Calcium ammonium nitrate formulations also vary, so check the specific label. Matching total nitrogen is a useful starting point, but timing and application methods may need adjustment with local agronomic advice.

What is the difference between granular ammonium nitrate, ammonium nitrate solution and UAN?

Granular ammonium nitrate is a solid product. Ammonium nitrate solution contains ammonium nitrate dissolved in water, while UAN contains both urea and ammonium nitrate in an aqueous formulation. Their composition, nitrogen concentration, storage requirements and handling equipment differ. Choose according to the specified application and grade, rather than physical form alone. In particular, an industrial ammonium nitrate solution or a water-soluble solid should not be assumed suitable for fertigation without checking its specification and intended use.

What should I do if ammonium nitrate becomes damp or caked, or its packaging is damaged?

Pause use of the affected stock and ask the site safety lead to assess it. Record the batch number, quantity, storage history and visible condition without disturbing damaged packaging or an unstable stack. Moisture, contamination and severe caking can require different responses. Do not attempt to restore flow by hammering, crushing, heating or blending the material. Contact the supplier for product-specific guidance, and have qualified personnel manage any segregation, recovery, return or disposal under the SDS and site procedures.

UAN

How do I choose between UAN28, UAN30 and UAN32?

Compare nitrogen requirements, storage conditions, equipment and delivered cost per kilogram of nitrogen. The numbers 28, 30 and 32 indicate nitrogen content by mass, so equal weights provide different amounts of nitrogen. Volume comparisons also require the density of each grade. Check the supplier’s storage-temperature guidance, particularly for cold conditions. A higher nitrogen concentration reduces the product mass needed to deliver a given quantity of nitrogen; the best choice also depends on handling costs and your application system.

How do I convert a nitrogen target into kilograms or litres of UAN32?

Use the nitrogen content by mass:

  • Product mass (kg) = required nitrogen (kg) ÷ nitrogen fraction
  • Product volume (L) = product mass (kg) ÷ density (kg/L)

For example, supplying 100 kg of nitrogen with a product containing 32% nitrogen by mass requires 100 ÷ 0.32 = 312.5 kg of product. Convert this to litres using the product density at the relevant measuring temperature. Keep any area units consistent. This example demonstrates the calculation; the nitrogen target itself should come from your crop nutrition plan.

What should I do if UAN develops crystals or sediment?

Crystals can form when UAN cools below its specified salt-out temperature. Sediment can also result from contamination or an incompatible mixture, so appearance alone cannot identify the cause. Record the grade, batch, storage temperatures and any materials added, then contact the supplier. Pause application until the cause and solution uniformity have been confirmed. Follow the supplier’s approved recovery procedure; adding water or applying heat without guidance can change the concentration or create handling problems.

Can UAN cause nitrogen losses or leaf burn, and how should it be applied?

Yes. UAN’s urea component can lose nitrogen through ammonia volatilization, while nitrate can be lost through leaching or denitrification under suitable conditions. Contact with foliage can also cause leaf injury. Select timing and placement for the crop, growth stage, soil, weather and equipment. Suitable soil injection or incorporation can reduce volatilization, while limiting leaf contact helps reduce scorch risk. Follow crop-specific recommendations when choosing the application rate, irrigation plan or any foliar use.

Can UAN be used through irrigation or mixed with other fertilizers and pesticides?

UAN can be used in suitable irrigation systems when the product’s instructions permit it. Confirm water quality, equipment-material compatibility, uniform delivery, injector calibration and backflow protection. Before mixing products, check all labels and obtain compatibility guidance for the actual water, concentrations and mixing sequence. An approved small-scale compatibility test can reveal precipitation or separation. A clear mixture, however, does not establish pesticide effectiveness or crop safety; these must also be confirmed before application.

Compound Fertilizers

How do 15-15-15 and 20-20-20 differ, and can I use the same amount?

Under the N–P₂O₅–K₂O labelling convention, the numbers represent mass percentages of nitrogen, phosphorus expressed as P₂O₅ and potassium expressed as K₂O. Both grades have a 1:1:1 ratio, but 20-20-20 contains more labelled nutrients per kilogram. For example, 75 kg of 20-20-20 provides the same labelled N, P₂O₅ and K₂O quantities as 100 kg of 15-15-15. This is a nutrient comparison only: solubility, nitrogen forms, additional nutrients and application instructions may differ.

How do I choose a compound fertilizer formula and rate for my crop, growth stage and soil?

Start with the crop, growth stage, realistic yield target and a representative soil test interpreted for your region. Account for nutrients from previous crops, manure, irrigation water and earlier fertilizer applications. Select a formulation and application schedule that meet the remaining requirements. Calculate all nutrients supplied, rather than nitrogen alone. If soil phosphorus or potassium is already sufficient, meeting the nitrogen target with a balanced NPK product may add nutrients that are not needed.

Can I dissolve ordinary granular compound fertilizer for drip irrigation or foliar spraying?

Use a product specifically confirmed suitable for the intended application. An NPK grade or granular appearance does not establish complete water solubility, low insoluble residue or suitability for leaf spraying. Check solubility, water-quality requirements, permitted concentrations and filtration guidance. Products that dissolve separately may still precipitate when mixed. For drip irrigation, choose a compatible fertigation grade. For foliar application, follow crop-specific instructions rather than converting a soil-application rate into a spray concentration.

Do I need calcium, magnesium, sulphur or micronutrients in addition to NPK? What does “+Fe” mean?

Check the full guaranteed analysis: the NPK grade does not describe every nutrient in the product. Soil, water and, where appropriate, plant-tissue tests can help identify additional requirements. “+Fe” indicates added iron but does not establish its amount, solubility or chelated form. Check the iron source and any declared chelating agent, because availability depends on conditions such as pH. Add nutrients to address an identified need; yellow leaves alone are not enough to diagnose a deficiency.

How do nitro-sulphate, nitro-chloride and urea-based compound fertilizers compare?

These names describe aspects of the formulation, so check the full analysis before choosing. Compare nitrogen forms, sulphur and chloride contents, nutrient concentrations and application instructions. Consider the crop and variety, chloride sensitivity, sulphur requirements, soil and irrigation-water salinity, placement and cost. Lower-chloride options may suit some sensitive crops, while chloride-containing products can be appropriate in other conditions. A urea-based formulation does not automatically provide slow-release performance; this requires a specific product feature and supporting specification.

Documents & Delivery

What are TDS, COA and SDS/MSDS documents, and which should I check?

Each document serves a different purpose:

  • TDS — Technical Data Sheet: describes technical properties and intended uses. Distinguish typical values from guaranteed specifications.
  • COA — Certificate of Analysis: reports results for an identified batch. Check the product, grade, batch number, test items, units and acceptance limits.
  • SDS — Safety Data Sheet, also commonly called MSDS: provides hazard, handling, storage and emergency information. It is not a quality certificate.

Request current documents for your exact product and grade, and confirm that the batch report matches the delivered material.

What should I check on delivery, and how should I report a quality or packaging issue?

Compare the product name, grade, batch number, quantity, labels, seals and packaging with your order and delivery documents. Record visible damage, leakage, moisture or unexpected appearance where safe. When reporting an issue, provide the order reference, affected batch and quantity, delivery date, photos and storage history. Hold affected material pending assessment, and follow site emergency procedures for leaks or other hazards. Complete any agreed document checks, sampling and testing: appearance alone cannot confirm product quality.

These references support the general topics identified beside each link. They do not certify Yongchang products, approve a specific installation or replace the current product specification, batch documents, SDS and local professional advice. Product selection and delivery checks should use the documents agreed for your order.

Back to top